Chapter 05
Flow wrappers form a flat film roll into a tube around the product, make a longitudinal (fin) seal, then seal and cut the cross seam between packs. SunAura Packaging Machines builds them in rotary-jaw, long-dwell and reciprocating (box-motion) versions across the SZ and SW series, including multi-servo machines such as the SZ-5800W.
| Model | Type | Typical application |
|---|---|---|
| SZ-280 | Rotary-jaw, compact | Bakery, biscuits, small solid packs |
| SW60X / SW80X | Rotary-jaw, up-rated frame | Larger packs, confectionery, bars |
| SZ-5800W | 7-servo reciprocating (box-motion) | Tall/long products, long-dwell seals |
| SZ-350 / SZ-450 / SZ-600 | Rotary or long-dwell frames | Family packs, trays, instant-noodle multipacks |
All SZ/SW-series flow wrappers and their servo/reciprocating variants are covered. If your nameplate carries an internal YS code for an SZ/SW machine, the procedures below apply unchanged.
| Freq. | Task | Standard |
|---|---|---|
| D | Clean product residue from cross jaws, fin wheels, forming box and infeed lugs | No carbonized film or product build-up |
| D | Check film path rollers turn freely; verify jaw temperature at setpoint | Free-rolling; ±5 °C |
| W | Inspect Teflon coating/tape on cross jaws and fin wheels | Intact, not worn through |
| W | Check infeed chain/lug condition and tension; inspect cut knife edge | No broken lugs; clean cut |
| M | Lubricate fin-shaft bearings, cross-jaw drive and chains per chart | NLGI #2 / ISO VG68 |
| M | Check jaw pressure, fin-seal pressure and knife timing | Per procedures below |
| Q | Inspect forming box for wear/scoring; check all drive belts | Smooth surface; belts not cracked |
| A | Gearbox oil, bearing repack, servo/encoder mounting and full timing check | Per master annual tasks |
| Point | Lubricant | Quantity | Freq. |
|---|---|---|---|
| Cross-jaw shaft bearings & linkage | NLGI #2 EP | 2–3 pumps | M |
| Fin-seal roller shaft bearings | NLGI #2 | 1–2 pumps | M |
| Infeed conveyor chain | Chain oil VG68 | Light film | M |
| Main drive gearbox | ISO VG68 gear oil | To sight line | A |
| Film tension / dancer pivots | NLGI #2 | 1 pump | Q |
| Symptom | Likely cause | Remedy |
|---|---|---|
| Weak / open cross seal | Low temp, worn Teflon/inserts, low jaw pressure, insufficient dwell | Raise temp to film spec; clean jaws; replace inserts; increase pressure/dwell |
| Burned or shrunk seal | Temperature too high or dwell too long | Lower temperature; reduce dwell; check thermocouple |
| Fin (longitudinal) seal open | Film not centered, worn fin wheels, low pressure/temp, wrong former | Re-center film; clean/heat wheels; adjust pressure; inspect former |
| Crooked / variable bag length | Eye-mark sensor, slipping feed, worn belts, timing drift | Clean/set sensor; tension belts; re-phase timing |
| Feathered cut or packs stay connected | Dull/nicked knife or knife-anvil gap | Replace/sharpen blade; reset anvil clearance |
| Film creases or wanders | Worn/damaged forming box, tension imbalance, misaligned rollers | Replace former; balance dancer; align rollers |
| Product crushed in seal | Infeed timing / push finger phasing wrong | Re-time infeed to jaw; check lug spacing |
| Servo / drive fault on start | Overload, encoder cable, parameter loss | Clear jam, check cables; restore archived parameters |
We use cookies to operate the site, analyse traffic and support your inquiries. You can accept all cookies or manage your choices. See our Privacy Policy and Cookie Policy.