Sales: [email protected] · WhatsApp +86 136 4542 9121 — CE-certified packaging machinery since 2008
SunAura Packaging Machines

Help Center

Precision packaging machinery, engineered and built in Qingdao, China since 2008.

Help & After-Sales Center

From installation and operator training to spare parts, remote diagnostics and scheduled maintenance, SunAura Packaging Machines engineers support your equipment across its entire lifecycle — anywhere in the world.

Service Lifecycle

Your After-Sales Journey

A clear, seven-stage process that begins before your machine leaves our workshop.

  1. 1

    Pre-Delivery Inspection

    Every machine undergoes a Factory Acceptance Test with your film and products where samples are provided.

  2. 2

    Delivery & Unpacking

    We confirm packing, documents and spare parts, and guide the on-arrival inspection.

  3. 3

    Installation & Commissioning

    Positioning, utility connection, parameter setup and a verified production trial.

  4. 4

    Operator Training

    Hands-on training for operation, changeover, daily checks and first-line fault handling.

  5. 5

    Remote Support

    Fast diagnosis by video call, AR guidance or secure PLC remote access.

  6. 6

    Preventive Maintenance

    Scheduled servicing protects uptime and extends equipment life.

  7. 7

    Overhaul & Upgrade

    Retrofits, capacity expansion and major overhaul keep the line competitive.

Warranty Policy

Limited Warranty & Coverage

SunAura Packaging Machines machinery is built for continuous industrial duty and backed by a standard limited warranty, with extended cover available at order.

What is covered

  • Defects in materials and workmanship under normal use
  • Mechanical and electrical components that fail within the warranty period
  • Repair or replacement of confirmed defective parts
  • Remote troubleshooting and commissioning defects
  • Software/parameter restoration for the supplied configuration

What is not covered

  • Consumables and normal wear parts (heaters, blades, belts, Teflon, cutting wire)
  • Misuse, abuse, neglect or failure to follow the maintenance schedule
  • Unauthorized modification or repair by third parties
  • External causes: power surges, water ingress, corrosion, unsuitable environment
  • Issues caused by film, materials or product quality
  • Freight, travel and labour for non-warranty calls

Standard period

12 months from commissioning or 13 months from the bill of lading, whichever comes first. An extended warranty (24/36 months) can be added before shipment.

How to make a claim

Keep the machine model and serial number ready, record a short video and photos of the fault, then submit a support ticket. We diagnose remotely first and ship parts or arrange service as required.

Installation & Commissioning

Prepare Your Site for a Smooth Start

Most commissioning delays trace back to site readiness. Confirm the items below before the machine or engineer arrives.

Pre-installation checklist

  • Level floor / foundation with the load capacity shown on the layout
  • Clear space for operation, changeover and maintenance access
  • Power supply (voltage / phase / Hz) with a dedicated breaker and reliable grounding
  • Clean, dry compressed air at the required pressure and flow
  • Suitable ambient temperature and humidity; no corrosive or explosive atmosphere
  • Infeed, conveyors and downstream equipment positioned and tested
  • Film, cartons and products on site for the production trial
  • Operators and maintenance staff scheduled for training

What commissioning includes

  • Unloading, positioning and levelling the machine
  • Connection of power, air and signal interfaces
  • HMI and servo parameter configuration for your format
  • Film / carton loading and format changeover setup
  • Production trial with speed and seal-quality verification
  • Safety-function check and Site Acceptance Test (SAT)
  • Handover of manuals, spare parts and maintenance schedule

A remote-guided, video-supported installation is available for standard machines when on-site travel is impractical.

Training Academy

Operator & Maintenance Training

Well-trained teams run faster, change over quicker and prevent the majority of avoidable stoppages.

SessionTopics coveredRecommended attendees
Machine & safety overviewConstruction, safety guards, interlocks, lock-out / tag-outAll staff
Control system & HMIRecipes, parameters, alarms, data backupOperators, maintenance
Standard operationStart-up, normal running, shutdown, quality checksOperators
Format / film changeoverFilm loading, pitch, forming box, quick-change partsOperators
Daily maintenanceCleaning, lubrication, inspection, sensor careOperators, maintenance
Fault recognition & resetCommon alarms, first-line troubleshootingMaintenance
Spare parts managementWear-part identification and stock levelsMaintenance, stores

Flexible formats

On-site hands-on training, recorded video tutorials and printed manuals in multiple languages. We can also run a train-the-trainer programme for larger teams.

Training outcome

Your operators independently run the line, complete changeovers, perform daily checks and resolve first-line faults with confidence.

Preventive Maintenance

A Maintenance Schedule for Every Shift

Disciplined, interval-based maintenance is the single biggest factor in machine availability and service life.

IntervalMaintenance tasks
DailyClean the machine and film path; check air pressure; wipe the photocell and sensors; verify seal temperature; test emergency stops; remove product debris.
WeeklyInspect sealing jaws and cutter; check belt and chain tension; lubricate per the lubrication chart; inspect guards and guides.
MonthlyInspect electrical terminals; check wear of consumables; verify temperature calibration; clean filters and cooling; back up HMI parameters.
QuarterlyInspect bearings and gearboxes; check servos and encoders; test all safety functions; replace air filters.
AnnualFull mechanical and electrical inspection; gearbox oil change; replace worn parts; recalibrate controls; review software and torque settings.

Use the specified lubricants — food-grade grease on food-contact or bakery lines — and keep the recommended wear parts in stock. Download the printable schedule from the download center, or read our preventive maintenance knowledge articles.

Troubleshooting & Fault Codes

Symptoms, Causes & Recommended Actions

Filter by machine family or use the search box at the top. Click any symptom to expand the likely cause and corrective action.

You can also browse the equipment families directly: flow wrappers, case sealers, case erectors, shrink wrappers, pallet wrappers and strapping machines.

Likely cause: seal temperature too low, speed too high, insufficient roller pressure or incorrect / damp film.

Action: Raise the temperature in small steps, confirm film suitability, check fin-seal roller pressure and alignment, and reduce speed for a seal-quality test.

Likely cause: crimp jaws misaligned, uneven temperature, excessive film tension or worn jaw serrations.

Action: Re-align and re-time the crimp jaws, balance left/right temperature and reduce film tension at the forming box.

Likely cause: photocell sensitivity or mode incorrect, dirty lens, guide rollers mis-set or printed mark contrast low.

Action: Clean the photocell lens, re-center the film at the forming box, then recalibrate the eye-mark sensor in the correct (light/dark) mode.

Likely cause: product pitch does not match film feed, infeed timing is off or products are too close.

Action: Adjust bag length / pitch and infeed timing, verify product spacing and check the push-lug timing on the infeed conveyor.

Likely cause: dull cutting blade, incorrect blade-to-anvil gap or cutting timing offset.

Action: Replace or sharpen the blade, reset the blade gap to the manual value and re-check cut timing.

Likely cause: failed heater, thermocouple or solid-state relay (SSR); loose connection.

Action: Check the heater resistance and thermocouple reading, inspect the SSR and fuses, and replace the failed component.

Likely cause: worn or gummed tape-cutting blade.

Action: Clean or replace the tape blade and confirm the tape is routed correctly through the blade assembly.

Likely cause: tape tension too high or low, or boxes entering off-center.

Action: Adjust tape tension, center the side guides to the carton and confirm flaps are fully folded before taping.

Likely cause: flaps not folded, size outside range or guides set too tight.

Action: Ensure leading/trailing flaps are tucked, reset width and height guides to the carton, and remove any damaged box.

Likely cause: worn suction cups, low vacuum, incorrectly stacked blanks or warped cartons.

Action: Inspect/replace suction cups, check the vacuum pump and filters, and square the blank magazine within specification.

Likely cause: flap-tucker timing, tape/glue timing or guide alignment out of set.

Action: Re-adjust forming-guide position and tucker/tape timing, and verify flat-blank dimensions against the set recipe.

Likely cause: tunnel temperature too low, dwell too short, insufficient airflow or oversized film.

Action: Increase temperature or reduce conveyor speed, adjust the air-flow directors and confirm film gauge and bag slack.

Likely cause: temperature too high, dwell too long or hot air concentrated on one point.

Action: Lower temperature, increase belt speed and re-direct airflow; confirm the film temperature rating.

Likely cause: insufficient perforation, poor air circulation or excess film.

Action: Add/improve perforations, adjust corner airflow and reduce excess film in the seal.

Likely cause: worn seal wire, damaged Teflon cover or degraded insulation.

Action: Replace the seal wire and Teflon cover, check electrical connections and confirm arm pressure.

Likely cause: tension too high, sharp load corners or poor-quality film.

Action: Reduce film tension / pre-stretch, add corner protectors and verify film grade for the pre-stretch ratio.

Likely cause: film clamp/cut unit timing or tail length incorrect.

Action: Adjust tail length and clamp/cut timing, clean the cutting blade and check the wipe-down brush.

Likely cause: insufficient top/bottom wraps, roped film or wrong overlap pattern.

Action: Increase wrap counts, set an even film band (avoid roping) and add a bonded top-sheet pattern where needed.

Likely cause: temperature/speed mismatch, low pressure or misaligned PTFE bands.

Action: Adjust temperature versus conveyor speed, check band tracking and pressure rollers, and confirm bag material.

Likely cause: worn, frayed or mis-tracked Teflon belt.

Action: Re-track or replace the PTFE belt, check roller alignment and confirm no residue is building on the band.

Likely cause: low pump oil, worn seals/gaskets, chamber leak or low gas supply.

Action: Check pump oil level and seals, inspect the chamber gasket and lid closure, verify gas pressure and mixing settings, and confirm sealing time.

Likely cause: feeder empty/mis-set, detection sensor fault or product/leaflet out of specification.

Action: Refill and re-set the feeders, clean/check the detection sensors and verify leaflet/product dimensions.

Likely cause: glue temperature low, bead position/size wrong or compression time short.

Action: Confirm glue temperature and bead pattern, check nozzle condition and increase compression / dwell time.

Likely cause: warped blanks, out-of-spec cartons or tucker/forming timing offset.

Action: Check flat-blank quality and dimensions, re-adjust forming-pocket and tucker timing and confirm the push-bar timing.

No fault entries match your search. Try different keywords or ask an engineer.

Spare Parts Center

Genuine Parts Protect Uptime

Genuine SunAura Packaging Machines wear parts are matched to your machine’s duty cycle and tolerances — non-genuine parts are a common cause of seal defects and secondary damage.

Machine familyRecommended spare / wear parts
Flow wrappersHeaters, thermocouples, SSRs, sealing-jaw inserts, cutting blade, Teflon tape, timing belts, eye-mark photocell, fuses
Case sealersTape-cutting blade, tape rollers, drive belts, guide bristles, springs
Case erectorsSuction cups, tape blades / glue heads, vacuum filters, seals, sensors
Shrink / L-barSeal wire, Teflon cover & tape, insulation strip, heaters, blower filters
Pallet wrappersPre-stretch rollers, film clamp/cut unit, drive belts, brushes
Band sealers / vacuumPTFE bands, heaters, ink wheels, gaskets, pump oil & filters
Common electricalFuses, relays, contactors, proximity sensors, air filters, specified lubricants

How to order

Quote the machine model and serial number and the part number from the manual (a photo of the nameplate helps). We confirm stock, price and freight; common wear parts ship quickly, while made-to-order items have a confirmed lead time.

Where to find the serial number

The identification plate is fixed to the machine frame / electrical cabinet and lists the model, serial number, voltage and date. Include it with every parts request to avoid mismatches.

Request a Parts Quotation

Remote & On-Site Service

Fast Diagnosis, On-Site When Needed

Remote technical support

  • Photo and short-video fault review by an application engineer
  • Live video call and AR-guided repair on the machine
  • Secure PLC / HMI remote access where connectivity allows
  • Parameter and recipe restoration from the supplied backup
  • Expedited genuine-parts dispatch

On-site service

  • Commissioning and Site Acceptance Test
  • Operator and maintenance training
  • Major repair, overhaul and line audits
  • Integration with existing equipment
  • Engineer dispatch with visa and travel handled by our team
SeverityDefinitionTarget response
S1 — CriticalLine down or safety-related stoppageWithin 8 working hours; remote support same day
S2 — MajorReduced speed or intermittent faultWithin 24 working hours
S3 — MinorCosmetic, documentation or non-urgent requestWithin 2 business days

Response targets are measured across working hours and time zones; customers with an extended warranty receive priority scheduling.

Returns & Claims

Transit Damage, DOA & Returns

On-arrival inspection

Inspect goods immediately on delivery and note any visible packaging damage on the carrier’s proof of delivery. Concealed damage should be reported within 7 days of receipt.

Damage or DOA claim

Send photos of the outer packaging, packing and the item, plus the packing list. Confirmed damage or dead-on-arrival items are replaced and the freight claim handled with our support.

Wrong item

Notify us within 7 days with the packing list and photos; we arrange the correct item and recovery of the original.

Non-warranty returns

Returns require prior authorization, an RMA number and the item in new, complete condition. Restocking and freight terms are confirmed in writing before return.

Upgrades & Retrofits

Extend Capacity Without Replacing the Line

Many machines can be modernized in place to raise speed, add automation or meet new standards.

Servo & control upgrades

Convert mechanical drives to servo, modernize HMI and restore parameter control.

Automatic feeding

Add auto infeed, feeders, magazine loaders and material-handling modules.

Speed & format expansion

Increase throughput or extend the range of sizes and products handled.

Safety & compliance

Guarding, interlock and CE-aligned safety upgrades on older equipment.

Connectivity

Data output, OEE monitoring and line-integration interfaces.

Audit & trade-in

On-site assessment, retrofit proposal and trade-in options.

Explore turnkey line capabilities or request a retrofit assessment.

Support Ticket

Open a Support Ticket

Tickets are logged and tracked by our after-sales team, with response according to the severity you select.

For photos or video, reply to the confirmation email from your inbox and attach the files.