Sales: [email protected] · WhatsApp +86 136 4542 9121 — CE-certified packaging machinery since 2008
SunAura Packaging Machines

Flow Wrapper Maintenance & Service Guide (Horizontal)

Precision packaging machinery, engineered and built in Qingdao, China since 2008.

Chapter 05

Flow Wrapper Maintenance & Service Guide (Horizontal)

Flow wrappers form a flat film roll into a tube around the product, make a longitudinal (fin) seal, then seal and cut the cross seam between packs. SunAura Packaging Machines builds them in rotary-jaw, long-dwell and reciprocating (box-motion) versions across the SZ and SW series, including multi-servo machines such as the SZ-5800W.

Catalog p.3–4Forming boxFin-seal rollersCross-seal jawsServo-driven

Models covered

Model Type Typical application
SZ-280 Rotary-jaw, compact Bakery, biscuits, small solid packs
SW60X / SW80X Rotary-jaw, up-rated frame Larger packs, confectionery, bars
SZ-5800W 7-servo reciprocating (box-motion) Tall/long products, long-dwell seals
SZ-350 / SZ-450 / SZ-600 Rotary or long-dwell frames Family packs, trays, instant-noodle multipacks

All SZ/SW-series flow wrappers and their servo/reciprocating variants are covered. If your nameplate carries an internal YS code for an SZ/SW machine, the procedures below apply unchanged.

Maintenance schedule (add to master schedule)

Freq. Task Standard
D Clean product residue from cross jaws, fin wheels, forming box and infeed lugs No carbonized film or product build-up
D Check film path rollers turn freely; verify jaw temperature at setpoint Free-rolling; ±5 °C
W Inspect Teflon coating/tape on cross jaws and fin wheels Intact, not worn through
W Check infeed chain/lug condition and tension; inspect cut knife edge No broken lugs; clean cut
M Lubricate fin-shaft bearings, cross-jaw drive and chains per chart NLGI #2 / ISO VG68
M Check jaw pressure, fin-seal pressure and knife timing Per procedures below
Q Inspect forming box for wear/scoring; check all drive belts Smooth surface; belts not cracked
A Gearbox oil, bearing repack, servo/encoder mounting and full timing check Per master annual tasks

Lubrication points

Point Lubricant Quantity Freq.
Cross-jaw shaft bearings & linkage NLGI #2 EP 2–3 pumps M
Fin-seal roller shaft bearings NLGI #2 1–2 pumps M
Infeed conveyor chain Chain oil VG68 Light film M
Main drive gearbox ISO VG68 gear oil To sight line A
Film tension / dancer pivots NLGI #2 1 pump Q

Wear parts (keep on the shelf)

  • Cross-seal jaw inserts — serrated sealing faces and their Teflon coating; replace when seals weaken or pattern is worn.
  • Fin-seal wheels and Teflon sleeves/tape.
  • Cut-off knife (straight or serrated) and anvil — a dull blade gives feathered or connected packs.
  • Forming box / former — replace when scored, dented or film drags (a worn former causes creases and mis-tracking).
  • Heating elements and thermocouples for jaws; infeed belts/chains and lugs; drive belts; carbon brushes on older DC machines.

Key service procedures

Setting cross-jaw temperature & pressure

  1. Set temperature for the film (typical 140–180 °C for OPP/cold-seal differs; follow the film supplier) and allow full stabilization.
  2. Run test packs; a correct cross seal is uniform across the width and peels with consistent resistance without burning.
  3. Adjust jaw pressure only enough to seal — excess pressure squeezes film out, wears inserts and loads the drive.
  4. On reciprocating machines confirm dwell suits film thickness; increase dwell rather than temperature for thick films.

Checking cut & eye-mark timing

  1. With registered film, center the eye-mark sensor on the mark and set sensitivity so it sees mark vs. base reliably.
  2. Jog and verify the cut falls on the register; use the phase/timing adjustment on the HMI in small increments.
  3. Confirm the knife meets the anvil squarely with no gap; replace a dull or nicked blade.

Troubleshooting

Symptom Likely cause Remedy
Weak / open cross seal Low temp, worn Teflon/inserts, low jaw pressure, insufficient dwell Raise temp to film spec; clean jaws; replace inserts; increase pressure/dwell
Burned or shrunk seal Temperature too high or dwell too long Lower temperature; reduce dwell; check thermocouple
Fin (longitudinal) seal open Film not centered, worn fin wheels, low pressure/temp, wrong former Re-center film; clean/heat wheels; adjust pressure; inspect former
Crooked / variable bag length Eye-mark sensor, slipping feed, worn belts, timing drift Clean/set sensor; tension belts; re-phase timing
Feathered cut or packs stay connected Dull/nicked knife or knife-anvil gap Replace/sharpen blade; reset anvil clearance
Film creases or wanders Worn/damaged forming box, tension imbalance, misaligned rollers Replace former; balance dancer; align rollers
Product crushed in seal Infeed timing / push finger phasing wrong Re-time infeed to jaw; check lug spacing
Servo / drive fault on start Overload, encoder cable, parameter loss Clear jam, check cables; restore archived parameters
WHEN TO CALL SUNAURAOperator-level: cleaning, temperature, film threading, sensor cleaning, knife change. Call service for repeated servo faults, timing that will not hold, gearbox noise or seal-quality problems that remain after inserts, temperature and pressure are verified.