Most buyers spec a palletizer first and sort out pallets later. That order is backwards. The pallet is the part that touches the gripper, the layer pattern, the stretch wrapper and the truck, and its dimensions, wear pattern and ownership model decide whether the palletizer runs clean or spends its shift faulting. In 2026 the wood-versus-plastic decision is no longer a simple price argument: pooled wood, reusable plastic and hybrid formats are spreading across export and retail supply chains, and the hygiene expectations of food and pharma lines push the choice harder. This post sets out the structural and commercial differences a buyer should pin down before signing a palletizer order.
Stringer versus block: the structural split to start with
Before comparing wood and plastic, sort the pallet into one of two structural families. A stringer pallet uses two or three long parallel boards (stringers) that the deck boards nail to; it is the cheaper, lighter format and it lifts on two sides (or four, if notched). A block pallet uses a grid of 4 to 9 or more blocks, allowing four-way entry by a forklift or pallet truck and carrying heavier, taller stacks. The choice is not cosmetic: a stringer pallet flexes under a tall layer and shifts on a turntable wrapper, while a block pallet sits flatter but weighs more and costs more to buy and repair.
For an automatic palletizer, the block format is usually the safer baseline. The gripper and layer-squaring tables expect a flat, rigid top deck; a flexing stringer top deck lets interlocked cases settle unevenly between layers, which is the classic cause of lean pallets that fall after wrapping. See how load containment choices interact with the finished pallet in our comparison of stretch wrap, shrink hood and strapping.
EUR/EPAL versus US GMA versus plastic: regional formats matter
A pallet bought in one market does not drop straight onto the equipment of another. The European EUR/EPAL pallet is 800 x 1200 mm, block-built, heat-treated and stamped; the North American GMA grocery pallet is 48 x 40 inches (1219 x 1016 mm), mostly a notched stringer format; Australian, Asian and Latin American markets each carry their own common footprint. Plastic pallets are molded to a footprint the buyer specifies, often to match one of the above so the fleet does not have to be re-engineered.
The practical risk is a palletizer whose layer pattern, gripper frame and conveyors are tuned to one footprint while inbound loads arrive on another. Mixed formats are common in contract packing and cross-dock operations, and they force a wider servo-centered conveyor, a longer infeed and a pattern library that holds recipes per format. PMMI, the association for packaging and processing technologies, keeps publishing guidance on how end-of-line equipment is specified around load and pallet geometry rather than around throughput alone.
Pooled versus owned pallets: who owns the pallet changes the spec
Under a pooled (CHEP-style) model, the user does not buy the pallet at all: a provider rents a circulating fleet, picks up empties and repairs them, and the user pays per trip. Under the owned model, the user buys, repairs and disposes of pallets in-house. The difference for the palletizer is not cost accounting — it is consistency.
Pooled fleets are standardized to a drawing and inspected between trips, so the pallet arriving at the automatic cell is close to spec every time. Owned fleets drift: broken stringers, missing blocks, reversed decks and weather-warped boards accumulate as the years pass, and the palletizer sees a slightly different load every shift. Smithers and Freedonia Group both track reusable and pooled packaging as a steadily growing segment of the load-shipping market, driven by retailers, exporters and food manufacturers who want a known pallet rather than a variable one. If you run owned pallets, plan a heavier inspection and repair loop; if you run pooled, write the exact pool drawing into the palletizer specification so the gripper and layer pattern are tuned to that drawing, not to a generic “wood pallet.”
Hygiene, washdown and the food/pharma line
Wood is porous. It absorbs moisture, retains odors and can splinter, and it carries visible wear that buyers of food and pharmaceutical product increasingly want to avoid on the load that leaves their dock. Heat-treated and ISPM-15 wood is acceptable for most export and grocery work, but washdown areas, open product and primary-contact pallets push buyers toward plastic, which wipes clean, does not absorb and can be sanitized. ISO standards for packaging safety and hygiene design, together with European food-contact and machinery directives cited by the European Commission, set the direction here: the pallet that reaches the consumer chain is treated as part of the packaging system, not as a throwaway asset.
Plastic pallets win on washdown, but they are not free of trade-offs. They are heavier to lift by hand, more expensive up front, and damaged units are usually recycled rather than nailed back together. For an automatic cell the hygiene advantage is real and the handling disadvantage is mostly absorbed by the machine — the operator never touches the pallet. This is why more food and pharma end-of-line projects in 2026 specify plastic or washdown-compatible wood for the outfeed, even where inbound product arrives on standard wood.
Weight, repair and the lifecycle number
A new wood stringer pallet weighs 15–25 kg; a block EUR-style pallet 20–30 kg; a comparable heavy-duty plastic pallet 15–25 kg for a hygienic nestable format and 30 kg or more for a rackable flat-top. That weight matters in three places: the pallet magazine and dispenser (heavier pallets need stronger lifters), the palletizer gripper (the payload check includes an empty pallet, not just the layer), and the truckload (a heavier pallet reduces net product per shipment, which exporters feel directly).
Repair economics run the other way. Wood is repaired — a new stringer, a few nails, a fresh block — for a fraction of a new pallet, and pooled providers price that repair into the rental. Plastic is not repaired board by board; damaged units go back to the recycler and a new molded unit comes in. The lifecycle comparison is therefore a five-year view, not a per-unit view: cheap wood pallets that break every trip can cost more in downtime and replacement than a more expensive plastic pallet that lasts ten years. The US Bureau of Labor Statistics tracks logistics and warehousing employment, and the long-run move toward fewer manual handling stations is the same pressure that pushes buyers toward palletizers that tolerate a known, well-maintained pallet fleet.
Dimensions, tolerance and the palletizer gripper
This is the section that earns its place in the spec. A palletizer does not care that a pallet is “48×40.” It cares about the actual top-deck width, the length, the height from floor to first deck board, the amount a used board is worn down, and the location of the forklift openings. Tolerance stacks up quickly on used wood: a board that sits 5 mm low on one corner changes the layer-squaring datum, and a pallet that is 10 mm out of square leans a 15-case-high stack by a visible angle by the time the fifth layer goes on.
A palletizer should be specified around the pallet the buyer actually runs: the footprint, the deck pattern (open, partial, closed), the entry type, the used-condition tolerance the fleet realistically holds, and the maximum empty-pallet weight the magazine must lift. The gripper and layer pattern are then designed against that pallet — not against a catalogue drawing. If the buyer later switches pools, moves from stringer to block, or starts importing on a different footprint, the gripper frame, the layer-squaring width and the pattern recipes may need revision. Writing the pallet drawing into the order is cheaper than retrofitting it after commissioning.
Wood, EUR/block, plastic and pooled pallets compared
| Pallet type | Up-front cost | Durability / repair | Hygiene | Recyclability | Typical use |
|---|---|---|---|---|---|
| Wood stringer (owned) | Lowest per unit | Repairable; wears unevenly in owned fleets | Porous; not washdown-grade | Recyclable / ground-wood reuse | General grocery, e-commerce, domestic distribution |
| EUR/EPAL block (pooled or owned) | Low-to-mid; rental per trip | Repairable; standardized pool inspection | Heat-treated; still wood, not sanitizable | Recyclable | European and intra-EU export, retail chains |
| US GMA stringer (owned / pooled) | Low-to-mid | Repairable; four-way notched | Porous; grocery-grade | Recyclable | North American grocery and CPG distribution |
| Rigid plastic (owned) | Highest per unit | Long life; units recycled, not nailed | Washdown, sanitizable, non-absorbent | Recycled into new molded pallets | Food, pharma, cleanroom export, captive closed loops |
What This Means for Your Buying Decision
The same logic applies when the palletizer sits inside a wider end-of-line project. Write the pallet format into the integration so the wrapper, the strapping station and the outfeed conveyor expect the same load the palletizer builds; that is the approach in our end-of-line integration guide. Buyers sourcing from overseas builders should also send the pallet drawing and sample photographs during quotation, because a palletizer tuned to a European block pallet will not layer a US stringer pallet as cleanly — see our notes on buying packaging machinery from overseas. And as manual pallet stations disappear across warehouses, the palletizer is increasingly chosen around a known pallet fleet rather than around the labor it replaces, a shift we track in the 2026 end-of-line automation trends. For the machine itself, the shortlist starts with our pallet wrapping machine buyer’s guide.
Frequently asked questions
Is wood or plastic better for a new palletizer in 2026?
There is no single winner. Wood (especially pooled block formats) is cheaper, repairable and widely accepted in grocery and general distribution. Plastic costs more up front but is washdown-safe, consistent and long-lasting, which matters for food, pharma and captive export loops. Spec the palletizer around whichever fleet you actually run.
Can a palletizer switch between wood and plastic pallets?
Often yes, but only with the right gripper frame, a servo-centered conveyor and a stored recipe per format. The empty-pallet weight, deck height and deck pattern differ between wood and molded plastic, so the magazine and layer-squaring settings have to be recalled by recipe rather than assumed.
Does a pooled CHEP-style pallet really improve palletizer uptime?
Usually, because pooled fleets are standardized to a drawing and inspected between trips, so the pallet arriving at the cell is closer to spec every time. Owned fleets drift as boards wear and break. If you run owned pallets, pair the palletizer with a firmer inspection and repair loop.
What pallet tolerance breaks an automatic palletizer?
Used wood pallets that sit 5 mm low on one corner or are 10 mm out of square will lean a tall layer over time. The spec should state the real tolerance your fleet holds — not a new-pallet drawing — and ask for a wider layer-squaring range and a magazine that detects a crooked or missing board.
Does the pallet choice affect the stretch wrapper behind the palletizer?
Yes. A flatter, rigid block or plastic top deck gives the wrapper a stable base; a flexing stringer top deck lets interlocked cases settle and lean after wrapping. Spec the pallet format and the wrapper pre-stretch together, rather than treating them as separate machines.
