Sales: [email protected] · WhatsApp +86 136 4542 9121 — CE-certified packaging machinery since 2008
Insights

Shrink tunnel heat and film ratio 2026: dwell time, gauge and energy balance for side-seal and L-bar bundling lines

Technical Knowledge

Nov 13, 2026 SunAura Engineering Team

TL;DR. A shrink bundler wraps product in film and passes it through a heated tunnel, where the film contracts tight around the bundle. The result depends on three settings that have to balance against each other: how long the pack spends in the tunnel (dwell), how hot the air is, and how much film the pack carries in the first place (the film ratio and gauge). Set the heat too high or dwell too long and the film wrinkles, burns or tears; set it too low and the bundle comes out loose, loose-fitting or uneven. Film that is too heavy wastes material and money, while a film that is too thin cannot hold the bundle through handling. In 2026, buyers comparing side-seal and L-bar shrink lines need to understand that heat balance and film ratio interact, what a good shrink pack looks like, the defects that point to a bad setting, and what these checks mean for a buying decision. This note walks through the two bundle methods, the heat and film variables, the common defects and their causes, the inspection checks, the decision signals, and the machine-selection questions that follow. Figures and settings are planning references; actual values follow your product, film and tunnel layout.

By Emily Chen, Packaging Process Engineer. Emily has worked on shrink bundling, case packing and secondary packaging lines for 11 years, from retail multipacks and tray bundles to printed-goods and household-product packs. Her floor work covers tunnel tuning, film gauge trials, defect review and changeover between bundle formats.

Why tunnel heat and film balance set shrink quality

Shrink wrapping is a two-stage process. The former or sealer wraps and closes the film around the product or multipack, then the tunnel heats the film until it contracts. The sealer decides the bag size and seal; the tunnel decides how that film tightens. A well-formed bag that meets an under-heated tunnel still comes out loose, and a hot tunnel cannot compensate for an over-sized bag or an over-thin film. The heat and film settings have to be read together, not tuned as separate knobs.

We see this on retrofit lines most clearly. A bundle that looks loose is often blamed on the tunnel being too cold, when the real cause is an over-sized film that cannot contract enough to pull tight, or a film gauge that does not shrink evenly. Raising the tunnel temperature to force the film then burns the edges or wrinkles the pack, and the line ends up chasing the wrong variable. The first step on a shrink line is to separate the sealer and bag factors from the tunnel factors before changing heat.

The machine families that form these bundles are reviewed in the shrink wrapping machine buying guide, and the sleeve, L-bar and side-seal bundle trade-offs in the shrink bundler multipack and tray guide. This note focuses on the tunnel heat and film-ratio side of the line.

Side-seal versus L-bar bundling

Two common sealer types feed shrink tunnels, and they form the bag differently. The table compares them on seal position, typical speed, bag size control and the setting that most affects the final pack.

Table 1 — Side-seal and L-bar shrink lines compared on seal, speed, bag control and main setting
Method Seal position Typical speed Bag size control Main setting to watch
Side-seal (continuous) Longitudinal side seal; film fed in a tube around product Higher, continuous for uniform multipacks Film width and tube diameter set by product width Film width ratio, tunnel dwell and heat on a steady flow
L-bar seal Two seals form an L across the end and side per bundle Cyclic, suited to varied or lower-volume packs Bag cut per cycle; more flexible for different sizes Bag cut length, seal dwell, tunnel match to cyclic packs

A side-seal line runs film in a continuous tube, closes a longitudinal seal, and feeds packs steadily through the tunnel. It suits regular multipacks at higher volume, and the film width relative to product width sets how much film wraps around the sides. An L-bar sealer cuts and seals a bag around each bundle in a cycle, which suits mixed sizes, shorter runs or packs that change often. The L-bar’s cut length and seal timing set the bag, and the tunnel has to match packs arriving in cycles rather than a steady stream. In both cases, the tunnel heat and the film ratio still have to balance against the actual bundle.

The heat balance: dwell, temperature and air flow

Three tunnel variables work together to bring the film to its shrink temperature. Dwell is how long the pack spends in the tunnel, set by conveyor speed and tunnel length. Temperature is the air or heater set point in the chamber. Air flow decides how evenly that heat reaches the film, through the fan, ducting and air curtains that move hot air around the pack. A tunnel that holds heat but does not circulate it leaves uneven shrink: sides or edges hotter than the top, or one side of the bundle tighter than the other.

Changing one variable usually means checking the others. If dwell is shortened to raise rate, the film may need a slightly higher temperature to reach shrink before discharge. If temperature is raised without a corresponding check on dwell, edges and seals can overheat while the center still settles. Air flow that is weak or blocked by a worn duct or dirty curtain produces hot and cold spots that look like an inconsistent film rather than a circulation problem. The right balance is a pack that contracts evenly on every face, with film laid smooth rather than wrinkled or pulled thin.

Tunnel condition affects the balance as much as the settings. Heater elements age and lose output, fans and ducts wear, and insulation degrades over time, so a tunnel that shrank well a year ago may need the setting re-checked after wear. Keep a record of the temperature, conveyor speed and air-flow setting used per bundle format, so a change in product or film can be tuned against a known good baseline. The wear and maintenance practice behind this is covered in the spare parts management guide.

Film gauge, ratio and lay-flat

The film side of the balance covers gauge, width ratio and how the film lays around the product. Gauge is the film thickness. A heavier gauge holds up better to rough handling and print but costs more per bundle and can resist shrinking, leaving a looser pack. A thinner gauge saves material but may tear, puncture or shrink unevenly, especially around sharp corners or a heavier multipack. The gauge should be matched to the bundle weight, sharp edges and distribution path, not chosen only on per-pack film cost.

Film ratio is how much film wraps around the product relative to its dimensions. On a side-seal tube, the film width versus product width sets the side overlap; on an L-bar bag, the cut length sets the film around the ends. Too little film leaves bare spots or a pack that cannot close; too much film leaves excess that bunches, wrinkles or pulls the bundle out of shape as it shrinks. A clean shrink pack has even overlap on the sides and ends, with no loose film flapping after discharge.

Lay-flat is how the film sits around the bundle before it enters the tunnel. A bag that twists, folds or rests unevenly on the conveyor shrinks into an uneven pack, because the heated film contracts from an irregular start. Check film unwind, bag formation and bundle squareness before blaming the tunnel. Material selection and gauge-reduction levers are reviewed in the film gauge reduction guide, and the per-bundle film cost calculation in the film cost calculation guide.

Common shrink defects and what they mean

Most shrink defects map to a heat or film variable, and recognizing the pattern narrows the diagnosis before the tunnel is opened up.

Table 2 — Common shrink defects, likely cause and floor check
Defect Likely cause Floor check
Loose or baggy bundle after tunnel Under-heated film, too short dwell, over-sized bag or heavy gauge Check temperature and conveyor speed; verify bag size and film gauge against product
Wrinkled or gathered film Too much film, over-heating, uneven air flow, or twisted lay-flat Review film ratio and overlap; check air circulation and bag formation before heat
Torn or punctured film at corners Sharp product edge, thin gauge, over-tight shrink or heat pulling too hard Check gauge and corner protection; review heat and film overlap
Film burned, discolored or brittle Temperature too high, dwell too long, or worn element overheating a spot Lower heat or speed; inspect heaters, ducts and insulation
Uneven shrink between sides or faces Blocked air flow, misaligned conveyor, film not centered, duct wear Check fans, curtains and ducting; verify bundle centering in the tube
Seal open or weak after shrink Seal bar timing or pressure, contaminated seal line, or heat softening the joint Inspect sealer jaw, seal material and seal-area cleanliness
Bundle drifts or topples on conveyor Uneven film pull, unstable product stack, or lay-flat twist Check bundle squareness, pattern and film unwind before tunnel tune-up

When a defect appears, work from the product and bag outward: confirm the bundle is square and the product stack stable, check the bag size and film lay-flat, then review the tunnel heat and air flow. Changing heat first on an unstable or over-sized bundle usually treats the symptom and creates a new defect elsewhere.

Inspection and quality checks on the shrink line

Inspection starts at discharge, where a bundle can be checked before it reaches cartoning or palletizing. A good shrink pack lies smooth and even on all faces, with film snug to the product, consistent side and end overlap, no wrinkles, bare spots, tears or burned edges, and a seal that stays closed. Sample packs should be checked at the start of a run, after a format or film change, and periodically through the shift, because heat and film drift through a production day.

Record the tunnel setting per format: temperature, conveyor speed or dwell, fan or air-flow setting, film gauge and film width ratio. That baseline lets the team reproduce a good pack after a changeover and diagnose a drift later. Track defects by type and product, so a recurring tear at one corner points to an edge or gauge problem, while random wrinkles suggest heat or air-flow inconsistency. The defect log and routine wear checks follow the same practice used on other packaging stations, outlined in the preventive maintenance guide.

Film quality itself should be verified against the pack. Check that the roll matches the stated gauge and width, that the film has no static buildup, splits or print registration issues that carry into the shrink, and that the roll supplier’s shrink-temperature guidance matches the tunnel setting. A film lot that runs slightly off specification can look like a tunnel problem until the lot is checked. Material and market context for packaging films draws on sources such as the Smithers packaging films reports.

What This Means for Your Buying Decision

For buyers comparing shrink bundling equipment in 2026, the tunability of the heat and film balance should be a stated selection criterion. Ask how dwell, temperature and air flow are controlled on the tunnel, whether settings are recalled per bundle format, and how the sealer bag size is matched to the product. A line that only shows a clean pack on one easy multipack will not reveal how it handles mixed sizes, irregular bundles or a film change, so bring your actual product and film to the test.

The practical decisions this points to are these. First, match the sealer type to your run profile: side-seal for regular high-volume multipacks, L-bar for mixed sizes or shorter runs. Second, confirm the tunnel covers your bundle range in size and weight, with enough dwell and air circulation to shrink evenly on every face. Third, choose film gauge and ratio against the bundle’s handling and sharp-edge risk, not the lowest per-pack film price. Fourth, require a sample run on your worst-case bundle before acceptance, and verify that settings, wear parts and manuals are handed over with the machine.

Where the shrink station feeds a broader end-of-line, consider how bundles reach the cartoner, strapper or palletizer, and whether the line balance holds at your planned rate. The integration and throughput side is reviewed in the end-of-line integration guide and the line balancing guide. The secondary load protection that follows the shrink bundle in transit is covered in the load containment guide.

Machine signals to watch

A few features point to a tunable, reliable shrink line. Independent control of temperature, conveyor speed and fan or air flow lets the balance be adjusted per product. Stored recipes recall the settings for each bundle and film, reducing setup drift after changeover. Accessible heaters, ducts and curtains make cleaning and wear inspection practical. A clear film unwind and bag-formation station keeps lay-flat consistent before the tunnel. A supplier who can produce a sample on your product and describe the film and tunnel range is more likely to support the line after install.

Be cautious where the tunnel heat is a single fixed setting, where the supplier cannot state the bundle size or film range the line handles, where air circulation is not described or adjustable, or where wear parts and manuals are vague. Those gaps usually show up as uneven shrink or repeated rejects once the line runs mixed SKUs and real production conditions.

Energy, utility and tunnel condition

Shrink tunnels are one of the more energy-heavy stations on an end-of-line floor, because the chamber holds heat through the run. Insulation condition, air curtains that keep heat in, heater efficiency and conveyor speed all affect how much energy a bundle uses. A tunnel that leaks heat through worn curtains or degraded insulation runs hotter to compensate, raising energy use and often producing uneven shrink. Check the utility draw against the available supply, and review how the tunnel warms up and holds temperature between runs. The energy-efficiency factors for packaging equipment are laid out in the end-of-line energy efficiency guide, and the compressed air and power review in the utility requirements guide.

Wear items on a tunnel include heater elements, fans, belts, curtains, seals and conveyor components. These should be listed with part numbers and lead times, so a worn element or curtain can be replaced before it causes a defect pattern. Routine inspection should check for heat loss, blocked ducts, worn belts and film residue on the tunnel walls. A tunnel that has not been serviced in years may need its settings re-baselined after parts are replaced, because the old setting was compensating for degraded output.

Questions to put before buying

  1. What bundle sizes, weights and product shapes does the line handle, and which are outside its range?
  2. How are tunnel temperature, dwell or conveyor speed, and air flow controlled, and are settings recalled per recipe?
  3. What film gauges and widths does the sealer and tunnel suit, and what film ratio does it recommend for our bundles?
  4. How does the line handle irregular, mixed or sharp-edged product, and what corner or film protection does it suggest?
  5. Which wear parts are listed, with part numbers, expected life and lead times?
  6. Can it run a sample on our worst-case bundle and film before acceptance, with reference packs from a similar product?
  7. What is the warm-up time, energy draw and maintenance access for the tunnel?
  8. How does the station connect to upstream packing and downstream strapping, wrapping or palletizing?

Scenario notes for 2026

A high-volume regular multipack line usually fits a side-seal line with a steady tunnel feed, where film width ratio and dwell are the main tuned variables. A mixed-SKU co-pack plant leans toward an L-bar sealer with quick change parts and recipe recall, because format changes define its real output. A heavy or sharp-edged product needs a gauge and corner review before the tunnel is sized, so the film can hold through handling. A plant running cold or chilled product should check how moisture and condensation affect film lay-flat and seal adhesion before locking the line in.

For an existing line with recurring shrink defects, start with the defect log and the bundle and bag condition before replacing the tunnel: confirm the stack is square, the bag size and lay-flat are correct, and the film lot matches specification. Then review heat, dwell and air flow in that order. Many loose or wrinkled packs trace to bag size or film rather than a tunnel that needs upgrading. The audit-first approach for an existing packaging line is outlined in the retrofit audits guide.

Validating the line before acceptance

Before sign-off, run the main and edge bundle formats through the sealer and tunnel on your own product and film. Check that shrink is even on every face, that overlap is consistent, and that seals hold after cooling. Time a format change and confirm the recipe and settings carry over. Record the tunnel and film settings that produce a sound pack, and review the wear-parts list, manuals and training handover. A reference installation running a similar bundle gives a useful check on long-term consistency and support response; the supplier continuity and engineering-capacity review is in the supplier continuity guide.

Film cost versus bundle reliability

Film is the recurring cost on a shrink line, and the temptation is to move to the cheapest gauge and narrowest film that will run. That trade-off deserves a full look. A thinner film lowers the per-bundle material cost, but it can raise rejects from tears, punctures and uneven shrink, and those rejects carry product loss, rework and downtime. A heavier film costs more per bundle but may hold a rough-handled multipack together through distribution. The right choice depends on bundle weight, sharp edges, stack stability and how far the pack travels, not the film price alone.

Film ratio is where waste often hides. An over-sized bag or an over-wide tube adds film to every bundle whether the product needs it or not, and that excess spends the whole run as material cost and often shows up as wrinkles after shrink. Reducing film width or cut length to the measured overlap the product actually needs is one of the cleaner savings on the line, because it does not compromise protection. Track film use per bundle over time, by format, so a film change or a bundle-size drift shows up in the cost record before it becomes a defect pattern. The cost-per-bundle calculation and gauge-reduction levers are reviewed in the film cost guide and the gauge reduction guide.

Printed and branded film adds its own check: registration, ink side and print alignment must carry through the shrink, and a film that shrinks unevenly can distort the graphics. Where pack appearance is part of the retail offer, the film trial should review the printed result after the tunnel, not just the seal and hold. Film suppliers usually publish a shrink-temperature and gauge range for their material, and the tunnel setting should sit inside that range rather than being tuned by ear.

Five buying mistakes on shrink lines

One: sizing the tunnel on the fastest pack only. The tallest, widest and heaviest bundle sets the tunnel height, width and dwell capacity. Average dimensions leave the line short on the worst SKU.

Two: treating heat as the only shrink variable. Bag size, film gauge, lay-flat and air flow all affect the final pack. Raising temperature to fix a loose or wrinkled bundle often burns or tears the film instead.

Three: choosing film on per-pack cost alone. A thin or narrow film that raises rejects and product loss rarely wins over five years. Match gauge and ratio to handling, sharp edges and distribution distance.

Four: skipping a sample on the worst-case bundle. An easy, regular multipack hides irregular-shape, mixed-size and sharp-edge problems. Test the bundle that stresses the line most before acceptance.

Five: leaving settings undocumented after install. Without a recorded temperature, speed, air-flow and film baseline per format, changeovers and operator changes drift the shrink quality until a defect batch appears. Recipe recall and a written setting record protect the pack.

Changeover, operator practice and layout

Changeover on a shrink line covers the sealer change parts, the film roll, the bag size or cut length, and the tunnel recipe. On a mixed-SKU line, how long this takes defines real output, so it should be timed during acceptance rather than assumed from the quoted cycle. Change parts should be accessible, stored near the station and labeled by format, and the recipe should recall the tunnel settings once the new bundle is loaded. Operators should be able to thread film, adjust the bag size and confirm a sound pack without relying on the supplier’s technician.

Operator training should cover what a good shrink pack looks like, how to read the tunnel settings, how to spot a drifting heat or air-flow condition, and the routine wear checks on heaters, fans, belts and curtains. A trained operator catches a loose or wrinkling bundle early, before it becomes a reject batch, and can tell whether the issue points to the bag, the film or the tunnel. The preventive routines behind this practice are in the preventive maintenance guide.

Layout affects whether the line runs at all. The station needs infeed and discharge clearance, a film-roll change position, guarding that does not block routine access, and headroom for the tunnel and film stand. Conveyor height should match the upstream packer and downstream strapper or cartoner, and the bundle should travel square into the tunnel rather than twisting on an uneven transfer. Measure the bay, the largest bundle envelope and the guarding footprint before confirming the machine size, the same layout review used for other end-of-line cells in the cell layout buying guide.

Where the shrink line is added to an existing floor, check how the new station aligns to the old conveyor and utilities, and whether the tunnel’s heat and ventilation fit the surrounding equipment. A retrofit that introduces a heated chamber next to a heat-sensitive packer or a dusty area may need ducting or spacing the original layout did not account for. The retrofit audit approach for existing packaging lines is outlined in the retrofit audits guide.

For a plant weighing a new shrink line against upgrading an existing tunnel, the starting point is the defect log and the wear record. If loose or wrinkled packs trace to bag size, film choice or a worn curtain and element that can be replaced, the existing station may hold its quality after service. If the tunnel cannot reach the dwell or air-flow balance the current bundle range needs, or the sealer cannot cover the bag sizes the line now runs, replacement is the more durable route. That audit-first check keeps the decision tied to measured defects and bundle performance, rather than a general sense that the equipment is aging, and it avoids buying tunnel capacity the floor does not need. Whatever route the plant takes, keep the tuned settings, film choices and defect records together after the decision, so the next format change or film trial starts from a documented baseline instead of a fresh guess. That record also makes later supplier reviews and spare-parts planning simpler, because the installed machine’s actual use can be compared against the original specification rather than against memory.

References and background sources

The heat and film reasoning in this note follows standard shrink-bundling practice and our floor audits. Market and material context draws on public industry sources: the Smithers packaging films and materials reports, the PMMI market research overview on packaging machinery, the interpack trade fair overview on equipment trends, and the Statista industrial robots topic for automation context. Temperature, dwell and film figures are planning references only; actual settings follow your product, film supplier guidance and tunnel layout.

Frequently asked questions

Emily Chen
Emily Chen Senior Mechanical Engineer — Case Erectors & Packers
10+ years in carton erection and case packing mechanism design

Emily designs the mechanical systems inside case erecting and case packing machines: blank feeds, magazine capacity, suction and flap-forming stations, product pickup and placement mechanics, and case discharge conveyors. She writes about erector and packer mechanisms, changeover times, dimensional limits and what a mechanical spec sheet should list.

Case Erectors Case Packers Mechanical Design