Sales: [email protected] · WhatsApp +86 136 4542 9121 — CE-certified packaging machinery since 2008
Insights

Case erector bottom closure buying guide 2026: tape vs hot-melt adhesive for RSC, HSC and wraparound cases

Technical Knowledge

Nov 16, 2026 SunAura Engineering Team

TL;DR. A case erector takes a flat, knocked-down blank, opens it into a square box, folds the bottom flaps, and seals the bottom before the case moves to filling or packing. The part that decides whether that bottom holds through stacking, handling and transit is the bottom closure method: pressure-sensitive tape or hot-melt adhesive. This guide walks the two methods down for 2026 buyers. It covers how each seals the bottom, the tape and adhesive specs that drive the joint, the machine formats that use each, speed and price bands, wear and consumable costs, the box and product conditions that favor one over the other, and the questions to put to suppliers before an RFP closes. Tape and hot melt are both mature, widely used processes; there is no universal winner. The right call follows your box construction, your plant environment, your required bond strength and how much maintenance the station can absorb. Price bands below are typical ex-works planning ranges before installation, controls, guards, freight and tooling. Speed figures are planning estimates on regular RSC cases; treat them as bands, not guaranteed cycle times. Top-flap closing and sealing at the case sealer after packing are a separate operation and are only referenced here.

By David Chen, Mechanical Engineer — Case Erecting & Sealing. David has commissioned and rebuilt case erectors and case sealers across food, household goods and e-commerce distribution centers, and has audited bottom-closure failures on more than 200 erected case lines.

What the bottom closure actually does on a case erector

Follow a blank through the erector once, because the closure method sits at the end of a short sequence that sets how clean the bond can be. The machine picks a flattened case blank from the magazine, drives it open so the side walls stand vertical, and folds the two lower flaps inward. Some erectors fold the bottom flaps with mechanical arms; others use belts, rails or a vacuum cup to tuck the flaps under. Once the flaps meet flat against the bottom, the closure station bonds them together, and the erected, sealed case discharges upright onto the outfeed conveyor.

The bottom joint has to hold three loads at once. It keeps the box square after erection, it carries the weight of whatever goes inside on the line, and it survives the compression of pallet stacking and the vibration of transport. A weak bottom bond does not always fail on the floor. It lets go after the case is filled, stacked on a pallet or dropped at a distribution center, which is why bottom-closure quality matters even when the top seal looks finished.

Two closure families dominate automatic case erectors. Pressure-sensitive tape lays a strip of coated BOPP or paper tape across the center seam of the bottom flaps; the tape adheres when a pressure roller presses it against the board. Hot-melt adhesive melts a solid thermoplastic bead, deposits it on the flaps, and the two flaps are pressed together while the adhesive cools and sets. Tape is a physical strip with a pressure-sensitive coating; hot melt is a fluid bead that wets the board and solidifies as it cools.

One point before the comparison: the erector and the case sealer are often confused on this question. The erector seals the bottom on an empty blank at the start of the line; the sealer closes and seals the top flaps after product is packed. A line can tape the bottom and glue the top, or run the same method at both ends. This guide focuses on the bottom closure on the erector. The top-closure comparison between tape, hot melt and cold glue is covered in our case sealer closure method guide; case format and board choices are detailed in the corrugated case specification guide.

Pressure-sensitive tape bottom closure

How a tape bottom seal forms

On a tape-bottom erector, a tape roll sits in a dispenser on the bottom closure head. Tape feeds off the roll through a guide and around a serrated cutting blade. When the folded flaps reach the closure position, the head presses the tape across the center seam of the bottom. A pressure roller, sometimes a pair of rollers, burns the tape down onto the corrugated face. The machine cuts the finished band free, and the case moves out with a tape strip running across the bottom center, with a short tail on each flap.

The bond comes from the adhesive coating on the tape backing, not from any heat or chemical reaction. Pressure from the roller flattens the tape onto the liner, and the pressure-sensitive acrylic or synthetic rubber coating grips the paper or BOPP surface. The joint holds as soon as the roller passes; there is no cooling or cure time to wait through. That is the main reason tape feels forgiving on a simple erector: the case can leave the station immediately.

Common machine tape widths run 48, 50 and 60 mm for standard RSC cases, with narrower tape for small cartons and wider tape for heavy or oversized cases. Tape backing is usually BOPP for general use, or a paper backing where recyclability or printing matters. Thickness and adhesive grade follow case weight, board condition and transit distance. A light retail carton on local distribution uses a thinner grade; an export pallet load needs a stronger, thicker tape with a higher-tack adhesive.

What drives tape bond quality

Three conditions decide whether a tape bottom holds. First, board contact. The tape has to sit flat against a clean, dry liner. Dusty board, loose corrugated fibers, oil or a coating that the adhesive does not wet leaves a weak surface bond that peels off under load. Recycled board and a worn liner surface raise this risk, because the liner itself can split before the tape releases.

Second, pressure and tape tension. The pressure roller has to flatten the full tape width onto the seam without bouncing on an uneven flap. Tape that rides up on a flap edge or sits partly off the center seam holds only on part of its width. Tape tension as it feeds off the roll sets whether the strip lays flat or wrinkles; a brake that is too loose lets the tape coil and crinkle, and one that is too tight pulls the strip off center.

Third, temperature and moisture. Pressure-sensitive adhesive loses tack in cold conditions and softens in heat. A cold storage plant, a chilled line or a winter loading dock can reduce grab until the tape warms up; a hot warehouse can make the adhesive flow and the band creep. High humidity or condensation on the liner also weakens the initial bond. These are reasons tape is usually paired with a grade matched to the plant climate rather than the cheapest general-purpose roll.

Tape wear parts and consumables

The tape station is mechanically simple and the parts list is short. The dispenser holds the roll and the brake sets feed tension. The feed or guide roller pulls tape through the head. The pressure roller burns the strip onto the board. The cutting blade slices the band after application. Guide strips and the head frame route the tape to the seam.

Consumables are the tape itself, plus the cutting blade, pressure roller and feed roller that touch every cycle. Tape is bought by the roll or carton and its cost tracks backing material, width and adhesive grade. Blade dulling shows up as a rough or hooked tape tail; a worn pressure roller leaves a band that is not fully burned down. On a mid-volume line, rollers and blades are standard wear parts that a maintenance team can change in place without a factory visit.

Where tape works, and where it struggles

Tape fits regular RSC and HSC cases on dry, room-temperature lines, where speed, simplicity and easy re-opening matter. It is common on e-commerce and fulfillment erectors because recipients can cut or peel the tape to open the box, and because the station needs neither heated equipment nor a hot adhesive supply. Tape stations are generally lower up front, have a shorter warm-up or setup, and are simpler for a small maintenance team to run.

Tape struggles on very heavy pallet loads where the center seam carries high compression, on oily or dusty board where the adhesive will not wet, and in extreme cold or heat where the adhesive grade loses performance. It also shows a visible strip across the bottom and can leave a tail that catches on conveyors if the cutter is off. For wraparound or odd-shaped cases, the flat tape path across an uneven bottom can be harder to seal cleanly.

Hot-melt adhesive bottom closure

How a hot-melt bottom seal forms

A hot-melt erector heats solid adhesive pellets or sticks in a heated tank or through a melter, keeps them at a controlled temperature, and pumps the molten adhesive to one or more spray guns or glue applicators on the closure head. As the folded bottom flaps reach the head, the guns apply a bead or a zigzag pattern of molten adhesive along the flap meeting line. The flaps are pressed together immediately, and the adhesive cools and solidifies in seconds, bonding the board faces together.

The bond forms as the melted adhesive wets the liner and sets as it returns to solid. Joint strength depends on adhesive temperature, bead size and pattern, pressure between the flaps, and the board temperature at the contact point. A bead applied too thin or too cold does not wet the board; a bead too large squeezes out and builds up on the head and rollers. The adhesive sets fast once pressed, but the joint reaches full strength as it cools, which takes a short moment after the flaps close.

Hot-melt grades are chosen for the board and the environment. General-purpose ethylene-vinyl acetate (EVA) adhesives cover standard board at room temperature. Polyolefin and specialty hot melts handle recycled board, colder plants, higher load weights or higher line speeds. The melter temperature, hose temperature and gun temperature are set to the adhesive manufacturer’s range, and the bead pattern and open time are matched to how fast the flaps meet after the adhesive lands.

What drives hot-melt bond quality

Heat control is the first variable. Adhesive that is too hot degrades, darkens, loses tack and can burn on the gun tip; adhesive too cold does not flow, leaves stringy strands or a partial bead, and does not wet the board. Melters, hoses and guns drift in temperature over time, and a thermocouple reading that sits a few degrees off shows up as inconsistent joints after months of running rather than on day one.

Second, bead volume and pattern. The applicator lays a round bead, a flat bead or a zigzag across the flap seam. Bead size follows case weight and board area; a heavy case needs more adhesive contact than a light carton. Too little adhesive leaves an open or weak seam; too much squeezes out onto the conveyor, the head and the product, and wastes glue. Gun clogging from charred adhesive or board dust breaks the bead pattern and leaves unglued sections.

Third, board and flap contact. Hot melt needs the two flap faces to meet squarely while the adhesive is still open. Flaps that do not fold fully flat, or that meet with a gap after an uneven erection, leave a bead bridging air rather than bonding board. Board temperature matters too: cold board pulls heat out of the bead faster and shortens the open time, so chilled lines often need a warmer adhesive grade or a shorter flap-to-press distance.

Hot-melt wear parts and consumables

The adhesive supply and applicator carry the wear and maintenance load. The melter heats and holds the glue; the heated hose runs adhesive to the gun; the gun module applies the bead. Nozzle tips, filters, screens and hoses are serviced or replaced on schedule. The adhesive itself is the recurring consumable, bought by box or pallet in sticks or pellets, and its cost follows grade, load and bead volume per case.

Maintenance runs deeper than a tape station. The melter, hose and guns need temperature monitoring, periodic cleaning of char buildup, and gun tip or filter replacement. A line that runs hot melt needs someone who can read adhesive temperature, troubleshoot a clogged gun and follow the melter’s maintenance schedule. Cleaning out old adhesive on a color or grade change is part of the process. Service skill and spare-part reach matter more here than on a tape machine.

Where hot melt works, and where it struggles

Hot melt earns its place on heavy cases, high-speed lines, recycled or coated board, and conditions where a tape strip cannot hold. The bead bonds across the full flap contact area, sits flush with the board without a raised strip, and handles higher compression and rougher transit. It is common on heavier shipping cases, export pallets, automated high-speed erectors and cases where the bottom must stay closed under stacking weight. The bond is also harder to open deliberately, which suits cases where tamper-resistance or a firm closure matters.

Hot melt struggles where the plant cannot support heated equipment. It needs power for the melter and heated hose, a supply of adhesive sticks or pellets, and maintenance that can keep guns and filters clean. It does not reopen cleanly, so a packed case that must be inspected or reworked cannot be peeled open the way a taped one can. Cold board and cold plant shorten open time, and the adhesive choice has to match those conditions. Char buildup, stringing and clogged tips are the recurring faults if temperature or cleaning slips.

Table 1 — Tape versus hot-melt bottom closure on bond, consumables, environment and service fit
Factor Pressure-sensitive tape Hot-melt adhesive
Bond mechanism Coated tape strip pressed onto liner; grip from pressure-sensitive adhesive Molten bead wets the flaps, sets as it cools and solidifies
Bond strength on heavy cases Moderate; holds regular and light loads, weaker under high compression High; bonds across flap contact area, suits heavy and export cases
Immediate handling Joint holds as soon as the roller passes; no cure wait Sets in seconds; reaches full strength as adhesive cools
Consumable BOPP or paper tape by roll; width 48–60 mm typical Hot-melt sticks or pellets; grade matched to board and climate
Main wear parts Cutter blade, pressure roller, feed roller, guide strips Gun nozzle, filter, screen, melter and heated hose service
Environment fit Dry, room-temperature lines; loses tack in extreme cold or heat Handles recycled and coated board; cold board needs matched grade and shorter open time
Re-opening Peels or cuts open cleanly; suits e-commerce returns and inspection Bond is hard to reopen without damaging the board
Maintenance level Low; simple mechanical station, standard parts Medium to high; heated system, temperature and gun upkeep needed
Typical price position Lower up front and simpler setup Higher up front for melter and applicator; consumable cost follows bead volume

Matching the closure to box style, board grade and product load

The closure method follows the case as much as it follows the machine. Before comparing erectors, settle the box you run and the weight it carries, because a tape grade and a hot-melt grade are both chosen against board and load rather than against the machine brochure.

RSC and HSC cases. Regular slotted containers and half-slotted cases have flat meeting flaps at the bottom that seal cleanly with either tape or hot melt. These are the standard cartons on most CPG, household-goods and e-commerce lines. Tape is the common default here on regular loads; hot melt moves in when the case is heavy, stacked high or bound for export.

Full-overlap and double-wall cases. Heavier shipping cases with overlapping flaps or double-wall board carry more weight and need a stronger bottom bond. Hot melt across the flap contact area usually handles these better than a single center tape strip, because the load compression spreads over more board area. Verify the adhesive or tape grade against the board weight and the pallet stack height in your test.

Wraparound and irregular cases. A wraparound blank wraps a product or a tray rather than forming a standard slotted box, and the bottom fold geometry can be uneven. Tape laying across a non-flat seam can ride up on a flap edge; hot melt adapts its bead to the meeting faces more easily on these shapes. Where the bottom profile varies by SKU, watch how the closure head follows the flap rather than assuming one method covers every blank.

Recycled and coated board. Board with high recycled content, a dusty liner or a light coating can reject tape adhesive, because the surface splits before the tape releases. Hot melt wets a wider range of liner surfaces, though the adhesive grade still has to match the board porosity. If your supply uses recycled board, ask both suppliers to test a sample blank from your actual corrugator, not a clean demo sheet.

Product and load conditions. A bottom seal on a light retail carton does not face the same forces as a bottom on a pallet of stacked goods. Heavy product, tall pallet stacks, long-distance export and cold-chain transit raise the bond requirement. Fragile or oily products that sit near the bottom flap can contaminate the board; an oily liner weakens both tape and hot melt, and the closure choice has to account for that contamination rather than only the case weight.

Buyer segmentation: who this closure choice fits

Closure selection shifts with volume, case mix, load weight, plant environment and maintenance capacity. The four profiles below cover the buyers we see most often on 2025–2026 erector projects. Match your line to the closest profile before comparing methods and suppliers.

Profile A: high-volume single-product line, multi-shift

This buyer runs a narrow case range at steady high output across two or three shifts. Priorities are availability, consistent bottom seals and low per-case labor. Changeover is rare, so recipe recall matters less than mean time between faults and consumable life. A high-duty automatic erector with a closure proven on your board fits this profile; wear parts and adhesive or tape should be stocked on site, and the station should be serviceable without a factory visit for routine changes.

Profile B: multi-SKU mixed line with frequent changeovers

This buyer runs several case sizes and flap profiles on one section, with board weight or load changing between SKUs. Effective output is shaped by changeover time and seal consistency across specs. Priorities are quick adjustments to tape width or bead pattern, and a closure that handles the full case range the line runs. A supplier’s mixed-line references matter more than a single peak cycle number.

Profile C: small plant or startup, low volume and limited budget

This buyer starts at a low case rate with a tight capital budget and limited maintenance staff. A simple tape-bottom semi-automatic or compact automatic erector handles light RSC cartons at this stage. Priorities are low entry price, small footprint, straightforward service and a clear upgrade path. Keep case range, conveyor connections and closure compatibility in mind for a later automatic machine, without buying high-speed capacity the plant has not secured.

Profile D: export, heavy-load or regulated market

This buyer ships heavy cases, pallet loads or products bound for markets with documentation and guarding requirements. Volume may fall in any profile, but the bottom bond must carry high stacking weight and the machine must meet the destination market’s safety baseline. Risk assessment and guarding design follow standards such as ISO 12100, and safety-related control circuits follow ISO 13849-1 where applicable. Compliance documentation and spare-parts reach in the destination region should be on the supplier shortlist from the first RFP.

Machine type comparison by speed, closure and price band

The table below compares common case erector formats by typical case rate, typical bottom closure, ex-works price band and best fit. Bands are typical 2026 planning ranges; final quotes depend on magazine capacity, case size range, controls, guards, infeed and outfeed, and local supply. Installation, commissioning, freight, tooling and spare parts are separate. The broader erector selection across random and fixed machines is covered in our case erector buying guide.

Table 2 — Case erector formats: speed, closure and price band (typical ranges)
Machine type Typical case rate Typical bottom closure Price band (typical ex-works) Best fit
Semi-automatic / hand-assist erector Up to roughly 6–10 cases/min Tape, light duty Low four figures to low five figures Profile C small plants; auxiliary low-volume erection
Automatic straight-line erector, mid-duty 10–20 cases/min Tape or hot melt Mid five figures to low six figures Mid-volume RSC/HSC lines; Profile B mixed runs
Servo random-case erector 15–30 cases/min, mixed sizes Tape or hot melt, recipe-driven Low to mid six figures Multi-SKU e-commerce and mixed-format lines
High-speed dual-head / inline erector 30+ cases/min, high duty Hot melt common; heavy-duty tape on some Mid to high six figures Profile A high-volume, heavy or export cases

Speed figures are cycle estimates on regular cases. Ask the supplier for an effective case rate under your actual blank size, board weight and SKU mix. A brochure cycle on an empty magazine overstates what the machine delivers on heavy, damp board.

Configuration matrix: options, necessity and price effect

Beyond the base closure method, options change seal quality, changeover and running cost. The matrix lists common options, how necessary they are for a typical line, and the typical way they move price. Markup is relative to the base machine; exact percentages depend on supplier, region and configuration.

Table 3 — Case erector bottom closure configuration matrix
Option Typical necessity Typical price effect What it changes on the floor
Hot-melt melter and applicator versus tape head High for heavy, recycled or export cases; optional on light dry RSC Substantial uplift over tape station Higher bond strength on heavy board; adds heated system maintenance
Servo case forming and flap folding High on random-SKU lines; recommended where flap fold consistency drives seal quality Moderate to substantial uplift Repeatable square cases per recipe; cleaner flap contact for the closure
Adhesive bead pattern control (bead/zigzag, volume per case) High on hot-melt heavy cases; low on tape machines Moderate uplift with gun and control Matched bead to load weight; reduces squeeze-out and glue waste
Tape width and quick-change head kit High where two or more case sizes run; low on single size Low to moderate one-time cost Covers future tape widths; cuts changeover between sizes
Seal presence or quality check sensor Recommended where open or weak bottoms are costly Moderate uplift with sensor and alarm logic Flags unsealed or weak cases before packing; feeds quality data
Case magazine capacity and automatic blank replenishment Recommended on unattended inline lines Moderate uplift Reduces blank loading stops; supports multi-shift running
Stainless or washdown construction Required for food contact, chilled or washdown zones; optional dry goods Substantial uplift over painted carbon steel Corrosion and cleaning-cycle compliance; no direct speed effect
Remote diagnostics and cycle data logging Recommended for multi-shift or distant plants Moderate uplift; possible recurring service fee Shortens fault recovery; supplies seal-quality and wear history
Spare closure-parts kit at order stage Recommended for long-lead or proprietary parts Low to moderate one-time cost Keeps availability high through the first service cycle

Do not stack every option onto every machine. A single light RSC line in dry goods gains little from servo recipes, bead pattern control or washdown steel. A heavy export line skipping seal monitoring or matched adhesive usually pays more in rejected cases and downtime than the option price.

Supplier tiers: global OEM, regional specialist, local or refurbished

Case erector suppliers fall into three broad tiers, and the right tier depends on case weight, volume, service expectations and budget. Closure quality and parts availability differ between them.

Tier 1: global packaging machinery OEMs. These brands sell complete inline erectors and often the surrounding end-of-line section, with engineering responsibility for case forming, closure matching and line integration. Lead times are typically longer and prices sit in the upper band, with support networks reaching most major markets. They suit Profile A high-volume lines and Profile D export or heavy-duty projects where documentation, spare-parts reach and long-term service matter. Proposals should include seal strength figures tested on your board, not only cycle speed.

Tier 2: regional specialists in case erecting and sealing. These manufacturers build solid erectors in a specific duty range, paired with local conveyor and integration partners. Prices sit in the middle band, lead times are usually shorter than Tier 1, and service engineers are reachable regionally. This tier suits Profile B mixed lines and most mid-volume projects. When the erector shares a line with machines from other specialists, clarify in writing who owns the interface, interlock signals and the line-level output guarantee.

Tier 3: local builders, semi-automatic suppliers and refurbished machines. This tier offers the lowest entry price and short lead times, often with manually assisted or reconditioned units. It suits Profile C startups and auxiliary low-volume stations, provided residual head condition, wear-part availability, remaining warranty and support terms are checked in writing. A refurbished erector can be a reasonable first step, but run it on your blank and board before acceptance; a weak closure that pops open after packing can cost more over five years than the saved purchase price.

Across all tiers, ask for references on lines running your board weight, case size and load type, and inspect a comparable installation if you can. Closure quality is easiest to judge on a running machine: watch the bottom strip or bead appearance, the case squareness, how often the head stops for a jam, and how fast an operator changes a worn blade or gun tip.

The five-year cost of a case erector station

The purchase price is the visible part of the decision; the five-year cost lives in consumables, labor, maintenance and the lost product from weak bottoms. The table outlines the TCO categories. Figures are planning categories; build your own numbers from measured tape or adhesive consumption, labor rates and downtime history.

Table 4 — Five-year TCO categories for a case erector bottom closure
Cost category What it includes How a weak closure drives it up
Purchase and machine hardware Magazine, forming mechanism, closure head, controls, guards, tools Oversizing the duty class raises up-front spend; under-sizing forces a later replacement
Installation and commissioning Placement, conveyor connection, utility work, setup, operator training Mismatched infeed, case clearance or power/air adds re-commissioning time
Consumables Tape rolls or hot-melt sticks/pellets bought by volume Weak seals lead to re-erected or re-packed cases; over-application wastes adhesive per case
Wear parts and service Blades, rollers, gun tips, filters, melter service, repairs Abrasive board and poor head design shorten part life; proprietary parts raise replacement cost
Direct labor Operators, jam clearers, blank loaders, changeover crew Unreliable stations need hands-on watch and rework that a dependable inline machine absorbs
Downtime and rejected cases Head faults, open bottoms, re-packed cases, held shipments Chronic seal failures pull cases off the line for rework; weak bottoms reaching customers trigger complaints and returns
Overtime and missed orders Extra hours to recover target output; late or split shipments A station that cannot hold line pace pushes production into overtime or missed delivery windows
Earlier retrofit or replacement Closure upgrade, second machine within the asset life Fixes deferred past commissioning usually cost more than specifying the duty class correctly at the start

A practical way to frame the hidden cost: each case that reaches packing with an open or weak bottom has to be caught, re-erected or, worse, opened at the customer’s dock. On a mid-volume line running 15 cases per minute, even a 3 percent seal failure rate adds up to hundreds of reworks per week. Multiply per-case rework time by labor rate and the complaint exposure by margin, and that figure is what a better closure pays back. Tape consumption follows the same logic: a head that wrinkles or double-tapes burns through more roll per case than one laying a steady, correct strip.

Ten questions to ask your supplier before the RFP closes

  1. Which bottom closure do you supply — pressure-sensitive tape or hot-melt adhesive — and what board weight, case size and load weight is the seal tested against?
  2. What seal strength or holding force do you guarantee for our board and case, how was it measured, and on what sample blank?
  3. What effective cases per minute can the machine deliver under our blank size, board weight and SKU mix, rather than the brochure peak on an empty magazine?
  4. For tape machines: what tape width and adhesive grade do you recommend for our cases, and how is the pressure roller set for our board?
  5. For hot-melt machines: what adhesive grade and temperature range, bead pattern and volume per case do you specify, and how is gun clogging prevented?
  6. Which wear parts are replaceable in the field, what are expected replacement intervals at our cycle count, and what are part numbers and lead times?
  7. Does the machine run multiple case sizes, and do guides, heads or guns swap as standard parts or need an upgrade kit?
  8. How are jams and mis-erected cases cleared, what guarding and interlock applies during access, and does the reset sequence protect operators and the adjacent conveyor?
  9. Does the closure include a seal presence or quality check, and what alarms or signals does it pass to the line control?
  10. What does the quote include: installation, commissioning, training, warranty length, spare-parts stocking, service response time and remote support, and what is excluded?

Five common pitfalls buyers hit

  • Choosing the closure on tape price or glue price alone. The consumable per case matters, but a weak bottom that reworks cases or fails in transit costs far more than the tape or bead saved. Judge total seal reliability on your board first, consumable cost second.
  • Matching a light tape station to heavy or export cases. A center tape strip on a heavy double-wall case can split the liner or open under stack compression. Check board weight and pallet height before assuming tape carries the load.
  • Ignoring plant temperature and board condition. Cold, damp or oily board weakens tape and hot melt alike. A closure that works on a dry demo sheet can fail on your dusty recycled liner; test your actual board in the demonstration.
  • Underestimating hot-melt maintenance. A heated melter, hose and guns need temperature monitoring, cleaning and trained service. A plant without that capacity may find a tape station cheaper to keep running despite higher consumable debate.
  • Testing on the supplier’s clean demo blank, not your production board. Board liner, recycled content and moisture vary between corrugators. Run your own blank through the demo, inspect the bottom seal and check case squareness before acceptance.

Recommendations by scenario

High-volume single line. Specify a high-duty erector with a closure proven on your board, stocked wear parts on site, and seal presence monitoring. Weight mean time between faults, recovery time and seal consistency above peak brochure speed. For heavy export cases, lean toward hot melt with matched adhesive and bead control.

Multi-SKU mixed line. Prioritize quick-change heads or recipes, servo forming where the load range justifies it, and a closure that handles every case size and board weight in your mix. Compare proposals on changeover minutes per SKU as well as steady case rate, and pick a supplier with comparable mixed-line references.

Small plant or startup. Start with a semi-automatic or compact automatic tape-bottom erector matched to current low volume and light RSC board. Keep case range and conveyor connections compatible with a later automatic machine, and avoid buying high-duty capacity the plant has not secured. A local or refurbished entry can work if closure condition, parts availability and support terms are verified in writing.

Heavy pallet or export line. Size the closure for working load and stacking height, specify safety guarding and documentation to the destination market’s standards, and confirm service and spare-parts reach in the shipping region. Run the same board and seal-strength checks as any other line, but build compliance and remote support into the shortlist from the first RFP.

Browse the full machine range on our case erectors overview page, and compare bottom and top sealing options across our case sealers range.

Frequently asked questions

Should my case erector use tape or hot-melt adhesive on the bottom?

Tape suits regular light-to-medium RSC and HSC cases on dry, room-temperature lines where simple maintenance and easy re-opening matter. Hot melt suits heavy double-wall or full-overlap cases, recycled or coated board, high-speed lines and export loads where the bottom must hold high stacking compression. Match the method to board weight, load, plant climate and your maintenance capacity, and test your actual board before deciding.

How strong is a taped bottom compared with a hot-melt bottom?

A tape bond holds through the pressure-sensitive strip across the center seam, while hot melt bonds across the full flap contact area as the adhesive sets. Hot melt generally carries higher compression on heavy cases, but a correctly graded tape on clean, dry board holds standard shipping loads well. Ask suppliers for a seal strength figure measured on your board rather than comparing tape and glue prices alone.

Does cold or humid weather weaken the bottom seal?

Yes. Pressure-sensitive tape loses tack in extreme cold and softens in heat, while condensation or a damp liner reduces grip. Hot melt loses open time on cold board and can chill too fast to wet the flaps. In chilled, humid or dusty plants, choose a grade matched to the conditions and verify the bond on samples pulled from your production board.

What maintenance does a hot-melt bottom closure need?

Hot-melt stations need melter and hose temperature monitoring, periodic cleaning of charred adhesive, replacement of gun tips, filters and screens, and adhesive grade changes done through the proper cleaning procedure. Tape stations mainly need cutter blades, pressure and feed rollers, and guide strips replaced on schedule. Hot melt calls for a maintenance team that can read adhesive temperature and troubleshoot a clogged gun.

Which wear parts on a case erector bottom head need regular replacement?

On tape machines the main consumables are the cutting blade, pressure roller, feed roller and guide strips. On hot-melt machines they are the gun nozzle, filter, screen and heated hose service, plus melter upkeep. Keep a spare set on high-cycle lines, and ask suppliers for replacement intervals at your cycle count, part numbers and lead times.

References: PMMI market research on packaging machinery and end-use markets, ISO 12100 machinery safety: general principles for design and risk assessment, ISO 13849-1 safety-related parts of control systems, OSHA workplace safety and machinery guarding guidance, Interpack packaging and processing trade fair industry context.

David Chen
David Chen Lead Packaging Engineer — Case Sealing & Cartoning
14+ years in secondary and end-of-line packaging

David leads our case sealing and cartoning engineering team. Over 14 years he has specified, installed and commissioned hundreds of random-size case sealers, top- and side-loading cartoners, and automatic case packers for food, household and industrial product lines. He writes buying guides and troubleshooting articles around seal quality, tape and hot-melt glue selection, and carton throughput limits.

Case Sealers Cartoning Machines Case Packing