Sales: [email protected] · WhatsApp +86 136 4542 9121 — CE-certified packaging machinery since 2008
Insights

Stretch Wrapper Pre-Stretch Carriage Buying Guide 2026: Standard vs Powered vs Fully Powered

Technical Knowledge

Nov 9, 2026 SunAura Engineering Team

TL;DR. A stretch wrapper in 2026 costs $8,000 (semi-automatic turntable) to $45,000 (fully automatic rotary-arm). The single biggest buying decision is not the wrapper itself — it’s the pre-stretch carriage. Standard (30% pre-stretch) uses 2x more film than fully powered (250–300% pre-stretch). Over 5 years, the carriage choice determines whether you spend $20k or $60k on stretch film. This guide compares all three carriage types, the math on film savings, and the 5 mistakes buyers make.

By Sarah Liu, Materials Engineer. Sarah has tested pre-stretch carriages from 8 manufacturers and tracks stretch film gauge reduction trends.

1. Why the carriage matters

The pre-stretch carriage pulls film through two rollers that stretch it before application. Smithers’ 2025 stretch film report notes that pre-stretch level is the single largest driver of film usage: a load wrapped at 30% pre-stretch uses roughly 2.5x the film of the same load at 250% pre-stretch.

PMMI’s 2025 secondary packaging survey found that 68% of buyers under-specify the carriage — they buy the wrapper first and upgrade the carriage later, which costs 2x more than specifying it upfront.

2. Three carriage types

Table 1 — Pre-stretch carriage comparison
Carriage type Pre-stretch Carriage cost Film usage per load Best for
Standard (drag brake) 20–30% $1,500–$3,000 ~250 g/load Low volume, occasional wrapping
Powered (motorized rollers) 130–180% $4,000–$7,000 ~120 g/load Mid volume, mixed loads
Fully powered (closed-loop feedback) 250–300% $8,000–$14,000 ~80 g/load High volume, uniform loads

3. The film math

Assume 200 loads/day, 2 shifts, 250 working days/year = 100,000 loads/year. At $2.80/kg cast stretch film:

Table 2 — Annual film cost by carriage
Carriage Film/load Annual film kg Annual cost 5-year cost
Standard 30% 250 g 25,000 kg $70,000 $350,000
Powered 150% 120 g 12,000 kg $33,600 $168,000
Fully powered 250% 80 g 8,000 kg $22,400 $112,000

Upgrading from standard to fully powered saves ~$47,600 per year — the carriage pays for itself in under 3 months on a 200-load/day line.

4. Which carriage for you

Table 3 — Decision matrix
Your situation Recommended
<20 loads/day, occasional Standard drag brake
20–100 loads/day, mixed sizes Powered 130–180%
>100 loads/day, uniform pallets Fully powered 250–300%
Light, unstable loads (bags, buckets) Lower pre-stretch (80–120%) to avoid crushing
Heavy, stable loads (boxes, bricks) Max pre-stretch 250–300%

5. Configuration checklist

  • Film width: 500 mm standard; 450 mm for small pallets; specify before ordering.
  • Film gauge: 23 μm standard; 17 μm works only with fully powered carriage (low stretch needs thicker film).
  • Top platen: required for unstable loads; adds $1,500–$3,000.
  • Photo-eye: needed for non-uniform load heights; diffused for black/dark product.
  • Clamp and cut: automatic film clamp/cut saves 30 seconds per load.
  • Spindle brake: motorized, not mechanical — consistent tension across the roll.

6. Common pitfalls

  1. Buying standard carriage “for now” — upgrading later requires a new carriage, not a retrofit. Specify powered or fully powered upfront.
  2. Using 17 μm film on a standard carriage — thin film cannot handle 30% pre-stretch without breaking. Match film gauge to carriage.
  3. Maxing pre-stretch on unstable loads — over-stretching crushes bagged or bucket loads. Drop to 80–120% for unstable product.
  4. Skipping the photo-eye — manual height adjustment wastes 30 seconds per load and causes over-wrap.
  5. No film roll holding capacity check — some carriages only accept 500 mm OD rolls; verify before ordering.

7. What questions to ask the supplier

  • What pre-stretch ratio does the carriage actually deliver (not just nameplate)?
  • Can it handle 17 μm gauge film? At what pre-stretch?
  • What is the film roll OD and core size? (3 in vs 203 mm core)
  • Is the tension closed-loop or open-loop? (closed-loop adjusts as film stretches)
  • What is the warranty on the carriage gearbox? (1 year vs 3 years)
  • Do you provide a film saving calculation based on my load profile?
  • Can I upgrade the carriage later? What does it cost?
  • What spare parts are recommended? (film cutter, clamp, brake)

8. Frequently asked questions

Sarah Liu
Sarah Liu Materials Engineer — Film & Strapping Technology
9+ years in stretch film, strapping band and consumable selection

Sarah evaluates packaging consumables against machine capability: film gauge and prestretch, PP versus PET and steel strapping, core width, tension settings and corner board use. Her articles connect film and band choice to machine settings, freight damage rates and total cost per pallet, rather than recommending the cheapest consumable on paper.

Stretch Film Strapping Packaging Materials